• Configures each pin of the board as the correct device type, ie keyboard, gamepad, analog, mouse, volume/power.
• Displays a pictorial representation of the board
• Fully real-time interactive. Reads and write board configuration "on the fly"
• Can be run in command-line mode or GUI
• Read/Save configuration to a file

Running from command line

This program can be run "invisibly" from a command line by simply appending the name of an already-saved IPC (config) file:
Winipac.exe <name of IPC file>

This will load the configuration specified. This will also cause a mode change if needed, if using multi-mode firmware. There is more on the "Multi Mode" product tab. Note the IPC file must be accessible by using its full path or saving it in the WinIPAC install folder.

Operation

PIN drop down

This displays the selected pin you are configuring. You can select pins from here or from the main graphic.

NICKNAME

You can type text in here which will remind you of which device this pin is connected to. The test is saved with the configuration (on the PC only) and is not sent to the board.

FUNCTION area

Here you configure the selected pin as the required device type and assign values to it.
You can select one of the radio buttons to define the pin as the following:

• Switch (which includes keyboard key, gamepad button and mouse buttons)
• Trackball/Spinner (includes optical steering wheels etc). This is only relevant to certain pins on the Ultimate I/O board.
  
  NOTE: Trackball/Spinner uses 2 pins per axis. The partner pin will also automatically be assigned. You can select X, Y or Z (wheel) axis.Trackballs use two axes (4 pins).
  Only the appropriate pins on the top two smaller connectors on the I-PAC Ultimate I/O can be assigned as trackball and spinner. It is recommended that you assign trackball on the left connector and spinner on the right otherwise you cannot use the special connectors for the U-Trak or Spintrak devices. The connectors for these devices are not unique. They use two or 4 of the total 48 input pins available.
  The I-PAC 2 and Mini-PAC also support trackball and spinner but these use dedicated pins.

Detail Configuration Example (Switch)

The switch is connected with one terminal to the required pin and other terminal to GND.

Select the pin by clicking on require pin in the graphic area.

Select "switch" radio button in the function area.

You now can select the control type eg whether keyboard key,

mouse button or gamepad button.

In the primary drop-down all possible keys are available plus macros defined separately (see later). Note that the I-PAC sends key scan codes just like a keyboard. It does not send characters so has no concept of upper/lower case. An upper-case key is a macro consisting of the Shift key plus the required character.

If required, you can select a secondary keycode. This is sent instead of the standard code when the I-PAC shift button is held. (This is by default the Start1 button but can be changed).

There is no need a secondary code unless you wish to use shift feature.

Macros

To assign a macro proceed as follows:

• Click on the MACRO tab
• Click NEW In the drop-down box, select the first character of the macro
• Click "Add Entry"
• In the drop-down box, select the second character of the macro
• Click "Add Entry"
• Repeat above 2 steps to add further characters
• Click "Add Macro".
• Return to the main tab. Select the macro in the drop-down when configuring the required pin.

Variable De-Bounce Delay

In the "Config" tab, the setting can be changed to 4 values as required. The default is the "standard" setting.

This value affects the rate at which the SAME input can be re-activated. Setting a low value will allow faster repeat of presses of the same button, but may also cause unwanted key repeat caused by switch bounce.

This is a specialized setting and should only be changed following testing with the specific switches being used. It does not affect overall performance because it only affects repeated action of the same input.

Dual Board Usage

This applies to the Ultimate I/O when one board has the standard firmware and a second board is connected with the "ID#2" firmware.

There is a command-line switch /2 which when used causes the board to skip the first board when detecting boards on startup.

This can be used in various ways. One method would be to copy the entire application to a different folder so you have two versions. Then edit the shortcut to the program to add the /2 switch.
Another way would be to use only one version and either apply the switch or not. Care would be needed when saving and loading IPC files.

If both boards are required to be reconfigured on the fly, a batch file would have two lines, each specifying a different IPC file and one with the /2 switch.

Upgrading Firmware

The firmware upgrade is a two-stage process.

First, the board is placed in firmware upgrade mode. Also a driver is installed on-the-fly if this is the first time an upgrade has been done on the PC.

Then, a program called UUPLOAD performs the upload of the firmware to the board. This program will not detect the board unless it has been placed into upgrade mode from within WinIPAC.

The following steps need to be followed:

• Run WinIPAC as administrator (right click and select "run as administrator")
• Ensure the board is detected and click "File, Firmware Upgrade".
• OK the prompts. The board should reset and change to "Firmware Upgrade Device" (If you have Device Manager open you will see the new device appear under the USB Controllers entry.
• A program called UUPLOAD.EXE should automatically start. If the process fails you can manually run this program if you have a "Firmware Upgrade Device showing in Device Manager
• Select the firmware file
• Uploading to the board should take approx 2-3 minutes. After that, the board should reset again and re-appear as a keyboard, mouse and game controller and be ready for use.
  
  Note: If the process will not work, you can try manually pre-installing the firmware upgrade driver by downloading the installer from this page which also contains additional information on the process and how to recover from failures.
  

The units were designed around MAME and normally you would use a front-end menu for selecting games. But of course, as the I-PAC emulates a real keyboard (without all the drawbacks) you can use any PC application which uses keyboard input.

Yes. You can use the fully programmable code sets of I-PAC to customise for any emulator or other application. Several popular front-end menus even have integrated support for downloading I-PAC codesets on-the-fly.

NO. Using the key-code programming is entirely optional. When the board is shipped, all codes are automatically assigned to MAME standard keys. As many people have found, this makes installation very quick and easy.

One method is to hack a keyboard, i.e. connect all the controls to the keyswitches so each button appears as a key. This is pretty unsatisfactory for several reasons: It takes ages to wire up as 2 wires need to be run to each switch.

Most arcade cabs have one side of all switches commoned so you have to re-wire everything.

Key Ghosting: This happens because of the matrix nature of keyboard encoders.

Extra buttons: With this solution, with some emulators you have to have extra buttons on the cabinet for functions such as "escape", "insert coin" etc. Nobody likes drilling extra holes in their nice original arcade cab!

Speed: Keyboard encoders use a scanning method. So each key is checked in sequence for a press or release. I-PAC does not use a matrix or scanning.

Shifted function keys will do various functions ie press "1 player start" and "fire" and you will insert a coin. Press "1 player start" and "2 player start" and you will jump back to the menu. You can also use the MAME game config menus with shift buttons, ie tab and enter are shift joystick right and left. The 1 player start button is always the shift button if you are using the standard MAME codes. In programmable mode you can assign any input to be the shift button and you can program all of the buttons to have shifted codes. The unique feature of the shift function is that it requires no dedicated extra button.

When the board is shipped it contains all standard MAME codes including the shift codes mentioned above. If you only ever use MAME and want a quick and easy install this will probably do for you. But if you need to, you can re-program as required, including "on the fly", and the board will remember your new settings.

You may find you need to change the assignment of keys for other emulators or maybe you don't want to have the shift functions of the MAME code set. The code set can be changed using the WinIPAC utility.

Normally you would install and test the board before getting into programming.

Yes the I-PAC will work on a MAC with USB. There is even a Mac version of the programming utility.

Yes the I-PAC will work on a Linux host. There is third-party Linux programming utility support (see Downloads page).

Dimensions shown below. Height is approx 17mm.

Click Here for older software versions for pre-2015 boards

Compatible with I-PAC Ultimate I/O, I-PAC 2, I-PAC 4, Mini-PAC, J-PAC. (2015-onwards boards only).

Click Here to Download Program

New boards are shipped with this version.

Latest firmware files (ver 1.55) for all 2015-onwards I-PAC, Mini-PAC and J-PAC boards plus all Ultimate I/O boards regardless of date.

I-PAC 4 has a later version 1.56 which enabled quad game controller support.

I-PAC Ultimate I/O new version 1.56 corrects an issue with mode changes not happening when trackball/spinner are connected.

NOTE: Attempting to upgrade a pre-2015 board which this firmware will render it inoperable.

All firmware now supports the Multi-Mode operation which enables switching to dual game controller mode or dual X-Input mode. Check the Multi-Mode tab on the product pages for more info.
Before upgrading ensure you have the I-PAC shift functionality enabled otherwise mode switching will not work. The default is Start1 being the shift control.
Also before upgrading to multi-mode firmware ensure the latest WinIPAC version is installed from the download page.
If the board comes up in Xinput mode after upgrading, this can be reset to standard keyboard by holding P1SW1 while connecting USB cable. See the Multi-Mode product tab on the I-PAC pages for full details.

Click here to download all Multi-Mode firmware versions, including ID#2 for the second board in dual-board UIO setups.

Version 1.56 firmware supports 4 game controllers on I-PAC 4. There is an important issue to be aware of with regards to WinIPAC support in Xinput mode, which is covered on the Multi-Mode tab page.

This is an alternative firmware version which enables the board to appear as a keyboard and dual standard game controller AT THE SAME TIME (both also with mouse). Note Retropie does not work with this configuration. The standard multiMode version (above) enables one device type at a time on the host (plus mouse) and this is required for Retropie. IMPORTANT: This version also requires a different version of WinIPAC for configuration.
This version does not support Xinput.
Unlike the Multi-Mode, this version automatically allocates each of the 2 game controllers on the respective side of the board so WinIPAC does not refer to player numbers, these are defined by the board markings. I-PAC 4 only supports 2 game controllers.

Click here to download all mixed-mode firmware versions.
Click here to download the special WinIPAC version for configuring mixed-mode boards.

Thanks to John K. Morris of Evolution Interactive for this software

Click here to download the new version for Intel Macs

Click here to download the older PowerPC version.

Linux software utilities are available. These cover several of our products and are being added-to. Please note we are not able to provide direct support for these utilities:

Linux Library and command line utilities developed by Katie Snow

Wiring Diagram.

Click here to download a PDF.

Recommended Wiring Procedure

Arrange the large switch connector on your left with the wires running towards the right, as shown in the right side of the diagram above, with the white polarising key at the bottom.
Working from the bottom of the connector, first connect the BLACK wire to the male connector on the ground harness.
Separate the rest of the wires into 4 groups. Start each group with the brown and red wires (bottom) and end with the purple and grey wires (top). You can ty-wrap the 4 groups close to the connector if you wish, or just lay the groups across the panel.
Now the wires from each group can be connected to the correct switches as shown on the diagram above. The table below may help, as this presents the connections in switch order and shows only the commonly-used switches
Then connect the ground harness to the other contact of each switch. Run along the controls in the most convenient path. You can miss out a connector if you need a longer routing as there are spares. Cut off the extra length.
If you are using the trackball/spinner harness connect the three other plugs to the trackball and spinner as shown and connect this to the board.
Ty-Wrap all wiring for neatness.

Reversing Trackball Axis
If you find one of the trackball axes moves "backwards", the resolution is to swap the X1 and X2 wires over (or Y1 and Y2). To do this, consult the diagram above and locate the correct pair of wires, at the main 30 way plug. The wire and contact can be removed from the black housing by carefully lifting the small tab on the side of the housing and pulling out. Swapping the pair of wires will reverse the direction of that axis.

Connecting Mouse Buttons
Mouse buttons can be connected to the trackball/spinner harness connector. These are not fitted as standard. They should be located as shown in the diagram above. You can swap over two spare wires from your switch harness. The wire and contact can be removed from the black housing by carefully lifting the small tab on the side of the housing and pulling out. Alternatively use two wires from the optional extension wire pack.
Keycodes, Programming and other Information.
All of the information on the I-PAC applies to the Mini-PAC. The default keycodes are the same, all programming information applies inclusing use of the WinIPAC utility, so check out the I-PAC pages for further information.

Troubleshooting Tips
All of the information on the I-PAC applies to the Mini-PAC. The LED indications are the same, all troubleshooting information applies, so check out the I-PAC pages for further information.

I-PAC Firmware version 50 Enhanced Modes

• Traditional I-PAC keyboard mode unaffected. This is still the default.
• Device mode can also be switched to Dual Directinput Game Controller or Dual Xinput Game Controller. I-PAC 4 now supports 4 game controllers.
• These modes appear as entirely different USB devices so there is no mixed-device confusion which causes issues in Retropie.
• Selected mode is maintained after power off/on.
• Standard Dinput and Xinput Game Controller modes are preset for ease of use without any configuration.
• For advanced users who wish to create custom Game Controller configurations there are customisable game controller modes.
• Modes can be switched by pressing Start1 (or user-set alternate I-PAC shift) and holding this, and Player 1 button 1 through 5, for 10 seconds.
• Modes can also be switched by loading an appropriate config file using WinIPAC including “invisibly” via a command line.

These modes apply to Player 1 and 2 controls.

Using WinIPAC, any input can be configured to any control including keys, power/volume, gamepad (Xinput or Dinput) across both players.
When this is done, keys configured as keyboard keys will respond in Mode 1, Keys configured as gamepad keys respond in modes 4 and 5.
Note this feature allows the entire 2-player panel to be configured as a one-player game controller if required, implementing every possible control.

Using WinIPAC, any key can be configured as mouse left or right button, Sleep, Wake, Vol Up, Vol Down. These will function in modes 1 and 4. (not Xinput).

When powered on, the LED will stay lit once the board has passed self-test and detected by the host system.

When switching modes, the LED will flash off, the number of times according to the mode number selected, after the 10 second period.

This is intended for use when WinIPAC is used for downloading configurations on the fly. This is the recommended method of mode switching if it is required to regularly switch modes.

Mode will switch automatically under the following conditions:

• If a keyboard-only configuration is downloaded and the board is currently in gamepad custom mode 4 it will switch to keyboard mode 1.
• If a gamepad-only configuration is downloaded and the board is currently in keyboard mode 1, it will switch to gamepad custom mode 4.
• If a gamepad-only configuration which includes an Xbox Home key is downloaded and the board is currently in keyboard mode 1, it will switch to gamepad custom mode 5.

Owing to the limitations imposed by the Xinput protocol, the following are NOT supported in Xinput modes but are supported in keyboard and Directinput modes:

Mouse buttons

Volume up and down buttons

Power, sleep, wake buttons

LED control (I-PAC Ultimate I/O only)

No trackball/spinner support

WinIPAC configuration changes take slightly longer in Xinput mode.

I-PAC 4 now supports quad Dinput and Xinput game controllers using firmware version 1.56. This is available in the firmware ZIP on our download page. 

When using WinIPAC, all custom settings for player 1 are automatically mirrored to the player 3 controller and all settings for player 2 are mirrored to player 4.

Please note an important limitation which applies only to the I-PAC 4 when in Xinput mode:

WinIPAC cannot be used for reconfiguring controls or switching modes on the fly when in Xinput mode. 

To create a custom Xinput configuration proceed as follows:
If the board is in Xinput mode, reset it to Dinput mode by using the hotkey Start1+P1SW4 for 10 seconds. If this does not work use the "backdoor" by holding in P1SW1 while plugging in USB.
If necessary, load in the default Dinput IPC file which can be found in the defaults sub-folder of the WinIPAC install.
Change settings as required. For Xinput, one of the controls must be set to HOME.
Save the file as an Xinput configuration.
Click "File, Force Board Reconfiguration". The board should switch to Xinput mode using the custom configuration.

Note that a mode switch is essentially the same as unplugging a USB device and plugging in a different one, into the same port. It will take the host PC up to 30 seconds to notice this and initialize the new device.

The mode switching can be confirmed by observing the on-board LED or “Devices and Printers” , the USB connect sound or other indication on the host.

If hotkey mode switching fails to work, check that Start1 (or another connection) is configured as an I-PAC shift control. If this feature has been removed in WinIPAC, mode switching will not work. Any stuck/shorted controls will also inhibit mode switching.

The board can be rest back into keyboard Mode 0 by pressing and holding the P1SW1 button on power up. This will work irrespective of the current board mode or input configuration. Note it must be a hard power-up or plug-in of the USB cable.